Site Overlay

FRENIC LIFT MANUAL PDF

FRENIC-Lift. FRENICG11S/P11S. FRENICVG7S. User’s Manuals and Technical Information. FRENIC-Multi User’s Manual. FRENIC-Eco User’s. FRENIC-Lift is an inverter designed to drive a three-phase induction motor ( hereafter For details about this product, refer to the FRENIC-Lift User’s Manual that. The FRENIC-Lift Series of exclusive AC Drives for operation of elevators are FRENIC-Lift AC Drives are available in a series with capacities ranging from

Author: Dajind Brakazahn
Country: Armenia
Language: English (Spanish)
Genre: Finance
Published (Last): 19 September 2009
Pages: 74
PDF File Size: 9.41 Mb
ePub File Size: 18.32 Mb
ISBN: 387-2-72659-517-4
Downloads: 11609
Price: Free* [*Free Regsitration Required]
Uploader: Tuhn

Tuning procedure What follows gives you a tuning procedure of manhal inverter for a motor using a multi-function keypad option. Setting Up Slide Switches 2.

In no event will Fuji Electric Co. Recommended Wire Sizes 2. To print the freniic completely, please, download it. You need to replace the option card.

Fuji Electric FRENIC-Lift series Instruction Manual

No part of this publication may be reproduced or copied without prior written permission from Fuji Electric Co. Terminal board illustrated in except Figure A. Put the front cover back in reverse order of. The standard motor and the inverter motor are protected in the range of all the frequencies. Possible Causes What to Check and Suggested Measures 1 No power supplied to the Check the input voltage, output voltage and interphase voltage unbalance.

Chapter 4 Running The Motor U, V and W respectively and that the grounding wires are connected to the ground electrodes correctly. Release the mechanical brake. Also remove the case fixing screws from the top.

Check that a mechanical brake is in effect. Push the front cover against the case of the inverter and slide it upward until the latch at its top engages with the case. Possible Causes What to Check nanual Suggested Measures 1 A high intensity noise was Check if appropriate noise control measures have been implemented e.

  DEFINISI SPONDYLOLISTHESIS PDF

The first letter is an manhal that identifies its group and the following two letters are numerals that identify each individual code in the group. You may drop the inverter or break it. Precautions For Use Precautions for use Driving a V When driving a V general-purpose motor with an inverter using ex- general-purpose tremely long wires, damage to the insulation of the motor may occur. Torque bias gain adjustment BTBG. When the inverter is used to run a general-purpose motor, the temperature Torque characte- of the motor becomes higher than when it is operated using a commercial ristics and tem Take care of the following items during work.

FUJI ELECTRIC FRENIC-LIFT SERIES INSTRUCTION MANUAL Pdf Download.

Consult your Fuji Electric representative if these terminals are to be used. The inverter connector RJ supplies the power to the keypad through the extension cable for keypad. For the lidt, check the rated values printed on the nameplate of the motor. U, V and W respectively and that the grounding wires are connected to the ground electrodes correctly.

FRENIC-Lift | Fuji Electric Global

Otherwise, the inverter may be broken if you turn the power ON. This chapter lists specifications including output ratings, control system, external dimensions and protective functions. When employing external manuzl At the shipment time, the inverter is set up for mount inside your equipment or enclosure so that cooling is done all internally. Date of purchase Inquiries for example, point and extent of breakage, uncertainties, failure phenomena, and other circumstances Page Don’t show me this message again.

Page 38 Table 2. Page 36 Table 2. Disable Times Times 1 to Page 82 [ 25 ] Over torque current Problem Reference torque current became excessive.

  EL TRAGALUZ DEL INFINITO PDF

Date of purchase Inquiries for example, point and extent of breakage, uncertainties, failure phenomena, and other circumstances. An undervoltage or an alarm has been occurred. Megger test of main circuit Use a VDC Megger and shut off the main power supply without fail during measurement. To use it follow the steps listed below. Brake trenic by output current Operation level 0 to ON delay time 0.

Trip with alarm after running for t he period specified by timer y03 2: Page 35 Table 2. Page 30 Grounding terminals G Be sure to ground either of the two grounding terminals for safety and noise reduction. Do not use a circuit breaker with a capacity exceeding the recommended capacity. Retry during the period specified by timer y Using the optional multi-function keypad allows you to start and stop the motor, monitor running status, and switch to the menu mode.

Init ialize all function code data to t he factory defaults H04 Auto-resetting 0: Page 18 1 Remove all of the base fixing screws from the top and bottom of the inverter. For your system design values, ask system designers about them.

Page 24 – Terminal arrangement and screw specifica Page 37 Table 2. Page In no event will Fuji Electric Co. Apply motor the inverter after consulting the motor maker.

Page 14 2 Warning plates Figure 1. Lighten the load or change the inverter for an upper size.